Your Complete Instruction for Installing a Bathtub
Your Complete Instruction for Installing a Bathtub
Blog Article
Right here down the page you can get lots of outstanding additional info when it comes to How to Install a Bathtub Yourself.
Installing a tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is readily easily accessible, the task can move easily; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and also set in the new one. Make sure you have certified on your own for the task as well as fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you may need a specialist plumber to make tube connections.
This short article will certainly assist you install a new tub in your bathroom if you have actually currently acquired a new tub and also don't need to alter the plan of your previous water system pipes.
Your devices as well as material list must comprise the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of removing the existing faucets can be rather bothersome due to the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, put the bathtub in the required position. The wood boards are valuable in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub until the spirit level checks out level.
To set up taps, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression join; after that do the very same for the various other tap.
Activate the water system as well as check all joints as well as new pipework for leakages and also tighten them if required. Fill the tub and likewise examine the overflow outlet as well as the typical outlet for leakages.
Finally, deal with the bath paneling as explained in the producer's user's manual. Tiling and sealing around the tub needs to wait till the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Protect the tap in position with the maker provided backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and the tiling, causing difficulties with wetness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog posting on A Step-by-Step Guide to Installing a Bathtub when doing research the search engines. Sharing is caring. You never know, you may very well be doing someone a favor. Thank you for taking the time to read it.
Schedule Now! Report this page